PDA

View Full Version : '93-'96 Fleetwood Mldg.


Kurt Arends
10-17-2014, 02:27 PM
I am in need of the wide lower stainless molding for the left fender for a '93-'96 Fleetwood(RWD). I only need the stainless molding that is in front of the L/F wheel opening. These cars still are not turning up very often in the salvage yards in my part of the world. Any help is appreciated.

Rocky Pollard
10-17-2014, 05:48 PM
try this:
http://www.ebay.com/itm/93-94-95-96-Cadillac-Fleetwood-LH-chrome-fender-molding-rocker-trim-panel-/311085028281?pt=Motors_Car_Truck_Parts_Accessories&hash=item486e1cd3b9&vxp=mtr

Kurt Arends
10-17-2014, 06:23 PM
I can't tell if it is the molding that goes in front of the wheel opening, or behind it..... and the seller does not state which it is.

Kurt Arends
10-17-2014, 06:28 PM
After looking at the photos of my coach again, it looks like this one is the molding that goes behind the wheel opening. I need the one that goes ahead of the wheel opening.

Kurt Arends
10-17-2014, 06:56 PM
This is the one I need, but I won't give anywhere near $295 for one!

http://www.ebay.com/itm/1993-96-Cadillac-Fleetwood-rocker-panel-stainless-trim-molding-left-front-fender-/261628173582?pt=Motors_Car_Truck_Parts_Accessories&fits=Make%3ACadillac%7CModel%3AFleetwood&hash=item3cea411d0e&vxp=mtr

Danny Ryder
10-17-2014, 08:21 PM
I am in need of the wide lower stainless molding for the left fender for a '93-'96 Fleetwood(RWD). I only need the stainless molding that is in front of the L/F wheel opening. These cars still are not turning up very often in the salvage yards in my part of the world. Any help is appreciated.

You talking drivers side? In front of the tire? On fender? I may still have one. WIll see.

Kurt Arends
10-17-2014, 10:14 PM
Danny,
Yes. The driver's side(left) front fender. Wide lower stainless molding in front of the wheel opening.

Attila Bethlenfalvy
10-18-2014, 10:08 AM
Cadillac Heaven has around a dozen parts '93-'96 Fleetwood in stock. Other than high mortality pieces like fuse box covers and driver door power controls they're fairly intact.

http://www.cadillacheaven.com/

Quick option, not cheapest.

Rocky Pollard
10-18-2014, 12:26 PM
I believe the piece I posted is what you need, the photo is up-side down and making it difficult to visualize. Look at the ends of the plastic moulding and you can see the sharp edge that goes next to the bumper and the other edge has a slight radius on the corner. The piece on the rear of the wheel well is much shorter.

Kurt Arends
10-18-2014, 02:48 PM
I believe the piece I posted is what you need, the photo is up-side down and making it difficult to visualize. Look at the ends of the plastic moulding and you can see the sharp edge that goes next to the bumper and the other edge has a slight radius on the corner. The piece on the rear of the wheel well is much shorter.

I think you are correct Rocky. The Pick-N-Pull yards in my area charge $4.99 per stainless panel and I have bought those long lower quarter moldings and the other fender stainless panels for spares at $4.99 each. I just can't find that particular piece right now. I just can't get myself to invest $95 in one small piece when I just started looking for it on Thursday.

Danny Ryder
11-05-2014, 07:10 PM
I think you are correct Rocky. The Pick-N-Pull yards in my area charge $4.99 per stainless panel and I have bought those long lower quarter moldings and the other fender stainless panels for spares at $4.99 each. I just can't find that particular piece right now. I just can't get myself to invest $95 in one small piece when I just started looking for it on Thursday.

I looked and didn't have any left.

Kurt Arends
11-07-2014, 03:57 PM
Found the wide stainless molding that I need today at the Pick-N-Pull 6 blocks from our office here in Omaha. It cost $3 plus tax!!! :D